Map Dictionary:
CMD0 - Specifies input and output locations for the command interface

DI - DeviceNet Input Table, as bits. DeviceNet tables are 125 words (16 bit) long.
DO - DeviceNet Output Table, as bits
DFI - DeviceNet Input, regarded as floats
DFO - DeviceNet Output, regarded as floats
DSI - DeviceNet Input, regarded as 16 bit integers
DSO - DeviceNet Output, regarded as 16 bit integers
DII - DeviceNet Input, regarded as 32 bit integers
DIO - DeviceNet Output, regarded as 32 bit integers
DTO - DeviceNet Output, regarded as text
DTI - DeviceNet Input, regarded as text

HI - Hardy Input Table (Boolean)

• HI0.0 - HI0.4 = digital input 1-5
• HI2.0-HI2.11 = Setpoint 1-12 output
• HI2.12-HI2.15 = Scale 1-4 in Motion

HSI - Hardy Input Table (Word)

• HSI1 = Instrument Status Word. See the bit definitions below
• HI1.0 = A/D error
• HI1.1 = A/D failure
• HI1.6 = Motion
• HI1.7 = Email Failure
• HI1.8 = NVR Failure
• HI1.9 = Infrared Failure
• HSI2 = Setpoint Output Word
• HSI3,HSI4,HSI5,HSI6 = Command Status Word, Chan 1,2,3,4. This 16-bit word holds the result status of mapped commands.
• HSI3.15, HSI4.15, HSI5.15,HSI6.15 = Command Status Data Valid. This bit is set when the rest of the status bits are valid.
• Status = 1,2,0x40 - calibration failed due to A/D error, A/D failure, or motion
• Status -8 (0xFFF8) = Hard Calibration failed, not enough ADC counts between high and low steps
• Status -6 (0xFFFA) = C2 Calibration failed, no C2 sensors detected
• Status -10 (0xFFF6) = C2 Calibration failed, bad C2 sensors detected
• HSI7 = Watchdog Word. Each bit represents the corresponding node(bit0=Node0 etc.) sending data. Five seconds after the last data packet arrives form any node, its bit is set to zero.
• HSI8,HSI9,HSI10,HSI11 - Status word for A/D channels 1-4
  • HSIX.0 = A/D error
  • HSIX.1 = A/D failure
  • HSIX.6 = Motion

HO - Hardy Output Table

• HO0.0-HO0.6 = Output Relay 1-7
• HO0.7 = Software LED (on back of unit)
• HO1.0-HO1.3 = Tare Channel 1-4
• HO1.4-HO1.7 = Zero Channel 1-4
• HO1.12-HO1.15 = Print Channel 1-4
• HO2.0-HO2.3 = C2 Calibrate Chan 1-4
• HO2.4-HO2.7 = Trad Cal Low Ch 1-4
• HO2.8-HO2.11 = Trad Cal High Ch 1-4
• HO3.0-HO3.9 = Send Custom Email 0-9

HFI - Hardy Float Input Table

• HFI4-7 = gross weight on chan 1-4
• HFI8-11 = net weight on chan 1-4
• HFI12-15 = peak weight on chan 1-4
• HFI16-19 = Rate of Change on channels 1-4

HFO - Hardy Float Output Table

• HFO[ 0- 7] - 8 user defined floating point scratchpad variables, saved in non-volatile RAM
• HFO9-20 - Setpoint 1-12 input
• HFO21-24 - Tare Wt ch 1-4
• HFO25-28 - Motion Tolerance ch 1-4
• HFO29-32 - Zero Tolerance ch 1-4
• HFO33-36 - AutoZero Tolerance ch 1-4
• HFO37-40 - Capacity ch 1-4
• HFO41-44 - Cal Low Wt ch 1-4
• HFO45-48 - Span Wt ch 1-4
• HFO49-60 - Setpoint 1-12 Target Wt
• HFO61-72 - Setpoint 1-12 Preact Wt
• HFO73-84 - Setpoint 1-12 Deadband Wt
• HFO85-HFO88 - Analog Output Card, Slot 0
• HFO89-HFO92 - Analog Output Card, Slot 1

HSO - Hardy Short Output table. A table of 16 bit integers.

• HSO0 Setpoint and Motion Word
• HSO1-4 Unit of Measure Ch 1-4
• HSO5-8 Decimal Point Ch 1-4
• HSO9-12 Grad Size Ch 1-4
• HSO13-16 WaverSaver Ch 1-4
• HSO17-20 Averages Ch 1-4
• HSO21-24 Use Auto Zero Ch 1-4
• HSO25-28 Zero Reminder Ch 1-4
• HSO29-32 Tare Reminder Ch 1-4
• HSO33-36 Channel 1-4 On
• HSO37 AutoPrint On
• HSO38 IR Enabled
• HSO39 Printer Baud
• HSO40 Printer Parity
• HSO41 Printer Data Bits
• HSO42 DeviceNet Baud
• HSO43 DeviceNet Node
• HSO44 RIO Baud
• HSO45 RIO Address
• HSO46 RIO Rack Size
• HSO47 RIO Quarter
• HSO48 RIO Last Quarter
• HSO49 ControlNet Address
• HSO50 Profibus Node Number
• HSO51 Profibus Out Size
• HSO52 Profibus In Size
• HSO53 Setup Menu Security
• HSO54 Calibration Menu Security
• HSO55 Options Menu Security
• HSO56 Mapping Menu Security
• HSO57 Medium Level Password
• HSO58 High Level Password
• HSO59-62 Calibration Type Ch 1-4
• HSO67-70 Calibration Month Ch 1-4
• HSO71-74 Calibration Day Ch 1-4
• HSO75-78 Calibration Hour Ch 1-4
• HSO79-82 Calibration Minute Ch 1-4
• HSO83-86 Calibration Second Ch 1-4

HTO - Hardy Text Output table.

• HTO0 Operator ID
• HTO1 Instrument ID
• HTO2-HTO5 Channel 1-4 Name
• HTO6-HTO15 Custom Text 0-9

HTI - Hardy Text Input table.

• HTI0-HTI3 Calibrator ID Ch 1-4
• HTI4 Model Number
• HTI5 Program Part Number
• HTI6 Firmware Revision

HII - Hardy Integer Input table.

• HII0 IP Address
• HII1 IP Mask Address
• HII2 IP Gateway Address
• HII3 IP DNS Address
• HII4 Serial Number

EO, EFO, ESO, EIO, ETO- Hardy Control Link Output tables

• EO = Hardy Control Link output, addressed as bits
• EFO = Hardy Control Link output, addressed as floats
• ESO = Hardy Control Link output, addressed as 16 bit integers
• EIO = Hardy Control Link output, addressed as 32 bit integers
• ETO = Hardy Control Link output, addressed as text

0I, 0FI, 0SI, 0SO, 0II, 0IO, 0TI, 0TO- Hardy Control Link Input tables, from Node 0

• 0I = Hardy Control Link input from Node 0, addressed as bits
• 0FI = Hardy Control Link input from Node 0, addressed as floats
• 0SI = Hardy Control Link input from Node 0, addressed as 16 bit integers
• 0II = Hardy Control Link input from Node 0, addressed as 32 bit integers
• 0TI = Hardy Control Link input from Node 0, addressed as text
• 1I, 1FI, 1SI, 1SO, 1II, 1IO, 1TI, 1TO- Hardy Control Link Input tables, from Node 1
• 2I, 2FI, 2SI, 2SO, 2II, 2IO, 2TI, 2TO- Hardy Control Link Input tables, from Node 2
• ...
• 9I, 9FI, 9SI, 9SO, 9II, 9IO, 9TI, 9TO- Hardy Control Link Input tables, from Node 9
• UI, UFI, USI, USO, UII, UIO, UTI, UTO- Hardy Control Link Input tables, from Node 10
• VI, VFI, VSI, VSO, VII, VIO, VTI, VTO- Hardy Control Link Input tables, from Node 11
• ...
• ZI, ZFI, ZSI, ZSO, ZII, ZIO, ZTI, ZTO- Hardy Control Link Input tables, from Node 15

RI, RO, RFI, RFO, RSI, RSO, RII, RIO, RTI, RTO - RIO tables (used if you have an RIO option card)

• RI, RO = RIO input/output, addressed as bits
• RFI, RFO = RIO input/output, addressed as floats
• RSI, RSO = RIO input/output, addressed as 16 bit integers
• RII, RIO = RIO input/output, addressed as 32 bit integers
• RTI, RTO = RIO input/output, addressed as text

CI, CO, CFI, CFO, CSI, CSO, CII, CIO, CTI, CTO - Communications Network tables (used if you have a ControlNet, EtherNet/IP or Profibus option card)

• CI, CO = Communication Network input/output, addressed as bits
• CFI, CFO = Communication Network input/output, addressed as floats
• CSI, CSO = Communication Network input/output, addressed as 16 bit integers
• CII, CIO = Communication Network input/output, addressed as 32 bit integers
• CTI, CTO = Communication Network input/output, addressed as text

MI, MO, MFI, MFO, MSI, MSO, MII, MIO, MTI, MTO - Modbus tables (used if you have Modbus)

• MI, MO = Modbus input/output, addressed as bits
• MFI, MFO = Modbus input/output, addressed as floats
• MSI, MSO = Modbus input/output, addressed as 16 bit integers
• MII, MIO = Modbus input/output, addressed as 32 bit integers
• MTI, MTO = Modbus input/output, addressed as text

HVO The members in this table are displayed in the configured units (lb, kg, oz, g)

• HVO0-3 = Zero Tolerance, channels 1-4
• HVO4-7 = Motion Tolerance, channels 1-4
• HVO8-11 = Auto Zero Tolerance, channels 1-4
• HVO12-15 = Scale Capacity, channels 1-4
• HVO16-19 = Calibration reference weight, channels 1-4
• HVO20-23 = calibration span weight, channels 1-4
• HVO24-27 = peak weight, channels 1-4
• HVO28-31 = tare weight, channels 1-4